Fisherbrand Octagonal Magnetic Stir Bar; Flat Surface; 0.31 in. Dia. (8mm); 1.5 in. L (38mm)

Fisherbrand Octagonal Magnetic Stir Bar; Flat Surface; 0.31 in. Dia. (8mm); 1.5 in. L (38mm) Reviews

Other Picture

Stir Bar, Magnetic; Fisherbrand; Octagonal; Flat surface; Pivot rings; Alnico-V magnet encased in PTFE; Dia.: 0.312 in. (8mm); Length: 1.5 in. (38mm)

Visit Store Now !!

Detail Products

Detail Reviews

Jul 31, 2011 19:15:23

PVC static mixer without injection port; 1-1/2" dia

PVC static mixer without injection port; 1-1/2" dia Reviews

Other Picture

PVC static mixer without injection port; 1-1/2" dia Feature

• PVC Mixers Without Injection Port
• Flow range: 15 to 35 GPM
• Mixer length: 10 in
• No. of elements: 4
• Pipe size (" ID): 1.5
• Pressure loss: 1.1 to 6.2 psi
• Part Number: AO-04668-63
• Package Quantity: EACH

Instead of mixing fluids with a motorized mixer before pumping, you can mix fluids while you pump them through a pipe line. In-line mixers prevent overmixing and undermixing, and resist fouling in your pipes or tubes. They are virtually maintenance free and need no spare parts. In-line mixers provide efficient mixing and can withstand large pressure changes—up to 1500 psi with smallest sizes. Mixing elements in pipe and tube mixers are securely attached to the mixer walls, so internal pressure changes cannot collapse elements and stop flow. These mixers are designed for blending light-viscosity treatment chemicals into a water stream. Each mixer is constructed of schedule 80 PVC and has four fixed, solid PVC mixing elements. Maximum working pressure is 150 psi. Connections are 150 lb raised face flanged ends.Note: these mixers are designed for high flow rates. They use four elements instead of six to minimize pressure loss.

Visit Store Now !!

Detail Products

Detail Reviews

Jul 30, 2011 19:28:05

Fisherbrand PTFE Disposable Stir Bar; 0.9 x 0.3 in. (2.5 x 0.8cm)

Fisherbrand PTFE Disposable Stir Bar; 0.9 x 0.3 in. (2.5 x 0.8cm) Reviews

Other Picture

Stir Bar, Magnetic; Fisherbrand; Strong magnets permanently coated with white PTFE; Disposable for contamination-free stirring; 0.9 x 0.3 in. (2.5 x 0.8cm); 100/Cs.

Visit Store Now !!

Detail Products

Detail Reviews

Jul 29, 2011 22:54:11

Extra support rod for stand 04344-00

Extra support rod for stand 04344-00 Reviews

Other Picture

Extra support rod for stand 04344-00 Feature

• General Accessories and Replacement Items
• Type: Accessories
• Part Number: AO-04344-10
• Package Quantity: EACH

science-lab-stirrers

Visit Store Now !!

Detail Products

Detail Reviews

Jul 28, 2011 21:12:05

Spider mixer support stand for 5 gallon vessel, 24"H x 5/8" dia

Spider mixer support stand for 5 gallon vessel, 24"H x 5/8" dia Reviews

Other Picture

Spider mixer support stand for 5 gallon vessel, 24"H x 5/8" dia Feature

• Spider Support Stand
• Type: Accessory
• Shaft dia: 0.625 in dia
• Shaft length: 24 in H
• Part Number: AO-50401-70
• Package Quantity: EACH

Spider support stands clamp onto the edges of square or rectangular pails, drums, and tanks. Model 50401-70 fits 5-gallon vessels; model 50401-71 fits 55-gallon vessels with rims up to 5/8" wide. Aluminum base has a stainless steel support rod.

Visit Store Now !!

Detail Products

Detail Reviews

Jul 25, 2011 13:58:03

Chemware D1069088 PTFE Stirring Rod 10" long

Chemware D1069088 PTFE Stirring Rod 10" long Reviews

Other Picture

Chemware D1069088 PTFE Stirring Rod 10" long Feature

• Inert to corrosives
• Non-stick and easy to clean
• Bendable into shapes
• 10 inches long
• Stir corrosive reagents

Chemware PTFE Stirring rods contain a fully enclosed steel insert for stiffness, yet can be bent to various shapes for use as a powered stirrer. Heat resistant to 550F and completely intert to highly corrosive reagents, Chemware PTFE Stirring rods are great for stirring where other materials can't. Anti-stick properties facilitate cleaning.

Visit Store Now !!

Detail Products

Detail Reviews

Jul 24, 2011 13:32:03

IKA High-Viscosity Mixer, 115 VAC

IKA High-Viscosity Mixer, 115 VAC Reviews

Other Picture

IKA High-Viscosity Mixer, 115 VAC Feature

• IKA High-Viscosity Mixers
• Powerful motor handles viscosities up to 50,000 cps
• Electronic controller maintains constant speed
• Chuck: accepts up to 0.375 in (10 mm) dia shafts
• Input power: 130 watts (Motor)
• Min speed (rpm): 50
• Max speed (rpm): 2000
• Motor (hp): 0.17
• Power (VAC): 115
• Max torque (in-oz): 85
• Brand: IKA
• Part Number: AO-50703-00
• Package Quantity: EACH

These powerful mixers handle liquid volumes up to 10 gallons (40 liters) and viscosities up to 50,000 cps (approximately the viscosity of synthetic polymers). Electronic speed control limits speed variation to 2%even under changing load conditions. The through-shaft design lets you easily adjust the shaft length and impeller depthplace or remove mixing vessels without repositioning the mixer. Aluminum and thermoplastic housing is designed to make efficient use of space. The quiet, maintenance-free motors are rated for continuous duty. Overload protection shuts down motor if maximum torque is exceeded. Electronic safety circuit produces a safe, smooth start to prevent spraying. Model features an analog output to record speed and torque.

Visit Store Now !!

Detail Products

Detail Reviews

Jul 23, 2011 16:59:17

Reversible dispersion mixers, 0 to 10000 rpm, 115VAC, 60Hz

Reversible dispersion mixers, 0 to 10000 rpm, 115VAC, 60Hz Reviews

Other Picture

Reversible dispersion mixers, 0 to 10000 rpm, 115VAC, 60Hz Feature

• Dispersion Mixers
• Efficiently disperse and mix hard-to-wet fine powders and settling solids
• Obtain reproducible results, which can be compared exactly
• Simple and quiet operation
• Description: Reversible dispersion mixer
• Min speed (rpm): 0
• Max speed (rpm): 10000
• Motor (hp): 0.75
• Power (VAC): 115
• Power (Hz): 60
• Part Number: AO-50401-02
• Package Quantity: EACH

Dispersion devices are used to incorporate extremely fine solid particles into the surrounding medium, such that the small particles do not settle under the force of gravity. Efficient dispersion is easy to obtain. First, the liquid is put into the container. Then, under moderate speed, the small particles are added. The impeller speed can be increased until the doughnut flow pattern is detected at a higher rpm. After this premixing steps the dispersion is carried out at high peripheral speeds that correlate to the tip speeds used in production by maintaining the doughnut. When dispersing small quantities, use high rotational speeds to match production results. High-Speed Dispersion Mixers have cruise control to maintain a constant speed even when viscosity changes for repeatable results. Model 04201-00 is a low cost solution for smaller quantities. Models 04201-02 and -03 are ideal for dispersion tasks in the lab and have heavy-duty clamps to tightly secure samples during maximum speeds. High-Speed Mixers include motor, control box, support stand, and four impellers in the following sizes: 20, 25, 30, and 40 mm. Reversible Dispersion Mixers allow you to change mixing directions. Downward "vortex" flow and upward "umbrella" flow ensure thoroughly mixed ingredients from center to wall and from top to bottom of the tank. Model 50401-01 has a solid-state, NEMA 4 control box that connects to the motor via a 5-ft cord with waterproof plug. Controller features on/off switch; pilot light; reset button; speed control dial; and mode selector (downward, stop, and upward). Choose air-drive model 50401-10 for mixing in hazardous atmospheres. The 1/2 hp air-drive motor is ideal for mixing solvents and volatile liquids. The motor accepts air line pressures up to 150 psig at 25 cfm. Reversible Mixers include support stand with anti-tip base and post providing 183/4" vertical travel, 6" horizontal travel, 303/304 SS shaft, pitched rotor, adjustable baffle plat

Visit Store Now !!

Detail Products

Detail Reviews

Jul 20, 2011 07:27:03

Pail mixer with rim clamp; 1/2- to 1-hp air drive, requires 22 to 40 CFM at 40 to 80 psi

Pail mixer with rim clamp; 1/2- to 1-hp air drive, requires 22 to 40 CFM at 40 to 80 psi Reviews

Other Picture

Pail mixer with rim clamp; 1/2- to 1-hp air drive, requires 22 to 40 CFM at 40 to 80 psi Feature

• Pail Mixer with Rim Clamp
• Convenient for mixing materials in a closed 5-gallon bucket
• Adjust motor along the centerline of the pail to align with the opening in lid
• Folding impeller allows you to mount the mixer without removing the lid
• Toggle switch on electric motor; air-control valve for speed adjustment on air-motor model
• Impeller size: 3.75 in diameter
• Motor (hp): 0.5
• Shaft length: 12 in
• Air input: 22 to 40 CFM at 40 to 80 psi
• Shaft material: stainless steel
• Part Number: AO-50500-30
• Package Quantity: EACH

What's included: mixers comes complete with stainless steel 12" shaft and 3-3/4" diameter folding impeller.

Visit Store Now !!

Detail Products

Detail Reviews

Jul 19, 2011 08:28:03

Handlebar mixer; 1/2" dia x 20.5"L shaft, 5" dia caged proller

Handlebar mixer; 1/2" dia x 20.5"L shaft, 5" dia caged proller Reviews

Other Picture

Handlebar mixer; 1/2" dia x 20.5"L shaft, 5" dia caged proller Feature

• Handlebar mixers
• Impeller size: 5 in dia caged
• Min speed (rpm): 100
• Max speed (rpm): 2000
• Motor (hp): 0.5
• Shaft dia: 0.5 in
• Shaft length: 20.5 in
• Max torque (in-oz): 1440
• Shaft material: stainless steel
• Part Number: AO-50500-35
• Package Quantity: EACH

science-lab-stirrers

Visit Store Now !!

Detail Products

Detail Reviews

Jul 18, 2011 03:47:04

Dynalon 303275-0007 5/16 x 1-1/2 Inch Teflon Octagonal Magnetic Stirring Bar (Pack Of 4)

Dynalon 303275-0007 5/16 x 1-1/2 Inch Teflon Octagonal Magnetic Stirring Bar (Pack Of 4) Reviews

Other Picture

Dynalon 303275-0007 5/16 x 1-1/2 Inch Teflon Octagonal Magnetic Stirring Bar (Pack Of 4) Feature

• Length: 38mm (1-1/2 inch); OD: 8mm (5/16 inch)
• Material: Teflon® PTFE
• Features an Alnico V magnetic core which is one of the most powerful permanent magnet alloys available
• Store in pairs to maintain magnetic strength
• Do not store in a random mass or drop on a hard surface

This octagonal PTFE stir bar features an Alnico V magnetic core which is one of the most powerful permanent magnet alloys available. Made of Teflon®, the PTFE thickness accounts for 18% of the stir bar diameter. Stir bar should not be stored in a random mass or dropped on a hard surface, especially steel. Stir bar should be stored in pairs to maintain magnetic strength. Material: Teflon® PTFE. Length: 38mm (1-1/2 inch). OD: 8mm (5/16 inch). Dynalon® #: 303275-0007.

Visit Store Now !!

Detail Products

Detail Reviews

Jul 17, 2011 03:28:10

Bel-Art 371210008 Scienceware Teflon Micro Flea Spinbar Magnetic Stirring Bar, Yellow, 2mm x 2mm Size

Bel-Art 371210008 Scienceware Teflon Micro Flea Spinbar Magnetic Stirring Bar, Yellow, 2mm x 2mm Size Reviews

Other Picture

Bel-Art 371210008 Scienceware Teflon Micro Flea Spinbar Magnetic Stirring Bar, Yellow, 2mm x 2mm Size Feature

• Ideal for vials, micro test tubes, centrifuge tubes
• Teflon PTFE coated
• Alnico V encapsulated magnet
• Available in yellow color
• Very small, efficient stirring bars

Micro (Flea) magnetic stirring bars are designed for stirring small volumes in vessels such as vials, tubes and gradient makers. Coated in PTFE, they are particularly useful for environmental testing and life science applications in which small sample volumes need to be prepared and evaluated. Yellow. Dimensions: 2 x 2 mm (.079 x .079").

Visit Store Now !!

Detail Products

Detail Reviews

Jul 16, 2011 08:07:05

316 SS tube mixer; 1/4" OD; 34 elements

316 SS tube mixer; 1/4" OD; 34 elements Reviews

Other Picture

316 SS tube mixer; 1/4" OD; 34 elements Feature

• Tube Mixers
• Mixer length: 11.5 in
• No. of elements: 34
• Pipe size (" OD): 0.25 in
• Pipe size (" ID): 0.19
• Viscosity (cp): 750 and up
• Part Number: AO-04669-60
• Package Quantity: EACH

Instead of mixing fluids with a motorized mixer before pumping, you can mix fluids while you pump them through a pipe line. In-line mixers prevent overmixing and undermixing, and resist fouling in your pipes or tubes. They are virtually maintenance free and need no spare parts. In-line mixers provide efficient mixing and can withstand large pressure changes—up to 1500 psi with smallest sizes. Mixing elements in pipe and tube mixers are securely attached to the mixer walls, so internal pressure changes cannot collapse elements and stop flow. These mixers consist of a series of fixed right- and left-hand elements. Tube and mixing elements are made of 316 stainless steel-ideal for mixing high-viscosity fluids such as epoxies. Mixers have plain ends and accept standard tube fittings (see pages 278-286 for compression fittings). Shpg wt 1 lb (0.5 kg).

Visit Store Now !!

Detail Products

Detail Reviews

Jul 14, 2011 22:52:03